Washer · Whirlpool

Whirlpool Washer Not Draining: Drain Hose, Pump Filter and Suds

Whirlpool washer won't drain or leaves clothes soaking? Check the drain hose, the pump filter on front-loaders and detergent suds, plus the F9 E1 and Sd codes.

Last verified November 16, 2026

Start here

Before you begin, make sure the washer is plugged in and set up normally —a kinked or clogged drain hose, or a blockage in the drainpipe or utility sink.

Start troubleshooting

Safety notice

Unplug the washer before opening the drain pump filter access panel.

View detailed safety tips

Most Likely Causes

Based on common issues for this problem.

  • 1A kinked or clogged drain hose, or a blockage in the drainpipe or utility sink
  • 2A clogged drain pump filter (front-load models that have one)
  • 3Too many suds from non-HE detergent, too much detergent, or "no splash" bleach
  • 4A drain hose pushed too far into the standpipe, or a standpipe taller than 96 inches
  • 5An overloaded, tightly packed or unbalanced load, or a gentle cycle with a slow spin

Also described as: “Whirlpool washer won't drain”, “Whirlpool washer full of water”, “Whirlpool washer leaving clothes wet”, “Whirlpool washer F9 E1”

Where to Start

Start with the display. Sd or Sud means suds, and F9 E1 means the drain is taking too long — both point you to a specific fix. Then check the drain hose, which is where Whirlpool's own drain checks start. On a front-loader, the drain pump filter is the next thing to clean.

Is there a code on the display?

Yes: Sd, Sud, F9 E1 or Int

Sd/Sud means too many suds, F9 E1 means a long drain, and Int means the cycle was paused or canceled. Follow that code's steps in Brand-Specific Info.

No code

Check the drain hose for kinks, clogs and how far it goes into the standpipe. Then check detergent, the pump filter (front-load) and the load.

Steps and error codes sourced from Whirlpool's official Product Help documentation (washer not draining, front-load error codes, F9 E1 and pump filter cleaning pages). Reviewed November 16, 2026.

Safety Notes

  • Unplug the washer before opening the drain pump filter access panel.
  • Expect water to come out when you open the pump filter. Put a large, flat container and a towel underneath first.

If your Whirlpool washer is leaving water in the tub or clothes soaking wet, the cause is usually something you can check without tools: the drain hose, too many suds, or a clogged pump filter on a front-loader. Whirlpool’s own documentation points to the drain hose installation first.

If the tub drains but the drum won’t spin, see the Whirlpool washer not spinning guide. More Whirlpool guides are on the Whirlpool brand page.

Diagnostic Steps

Your progress

0 of 5 steps checked

  1. Check the display for a drain code

    What to look for
    Sd or Sud, F9 E1, or Int on the display.
    What it indicates
    Sd or Sud means there are too many suds for the washer to spin the water out, so it pauses and extends the rinse to break them down. F9 E1 means draining is taking longer than expected, typically over eight minutes. Int means the cycle was paused or canceled; the washer may take 20 to 30 minutes to stop spinning and drain, and shows Int during that time.
    What to do
    For Sd or Sud, let the washer finish its extra rinses — they may repeat several times — then check your detergent. For F9 E1, go to the drain hose check. For Int, wait for the washer to finish draining. The Brand-Specific Info section below has the full steps for each code.
    If nothing changes
    If there's no code, check the drain hose.
  2. Check the drain hose

    What to look for
    Kinks or clogs in the hose, a blocked drainpipe or utility sink, how far the hose goes into the standpipe, and tape around the hose.
    What it indicates
    Whirlpool says a washer that won't drain may be down to an installation error. A kinked or clogged hose restricts the water. If the standpipe is taller than 96 inches, the washer can't pump the water out and it may flow back in. On front-loaders, a hose pushed more than 4.5 inches (113 mm) into the drainpipe can let drained water siphon back into the washer.
    What to do
    Straighten the hose and remove any blockage from the hose, the drainpipe or the utility sink. Use the U-shaped drain hose form from the installation instructions — it sets the correct hose length in the drainpipe. Don't tape the hose into the drainpipe; it should be loose yet secure, with an air gap between hose and pipe.
    If nothing changes
    Check what detergent you're using.
  3. Rule out excess suds

    What to look for
    Non-HE detergent, more detergent than the label calls for, or "no splash" or "easy pour" chlorine bleach.
    What it indicates
    Too many suds can stop the washer from pumping water out and spinning, or make it spin at a reduced speed and leave very wet loads. Whirlpool says "no splash" and "easy pour" chlorine bleaches contain a thickening agent that can create excess suds.
    What to do
    Use only HE (High-Efficiency) detergent, and measure it. HE detergents come in different concentrations (2x, 4x, 8x), so follow the dosing on the bottle for the load size and soil level. If you have very soft water, you may need less. Switch to regular liquid bleach if you've been using a "no splash" type.
    If nothing changes
    On a front-loader, clean the drain pump filter. On a top-loader, check the load and cycle.
  4. Clean the drain pump filter (front-load models)

    What to look for
    Lint, dirt or small items clogging the drain pump filter, usually at the front bottom of the washer, behind the bottom drawer on some models.
    What it indicates
    Over time, the filter can clog with dirt, lint or other items, and a clogged filter makes the washer drain slowly or not at all. Whirlpool recommends cleaning it every few months, or as needed.
    What to do
    Unplug the washer. On models with a storage drawer, remove the drawer to reach the filter. Put a large, flat container underneath, release the small black drain hose from its clip, remove its plug and let the water drain out. Replace the plug and clip the hose back. Lay a towel down, then turn the filter counterclockwise to remove it. Pull off clumps of lint by hand and rinse the rest away with water. Turn it back in clockwise as far as it will go, with the handle as close to vertical as possible. Check your owner's manual if your model's filter is in a different place.
    If nothing changes
    On front-loaders, also clean the small drain holes inside the door seal (bellow). If they clog, the washer may not drain well. Then check the load and cycle.
  5. Check the load, the lid or door, and the cycle

    What to look for
    An overloaded, tightly packed or unbalanced load; a lid or door that isn't fully closed; or a gentle cycle selected.
    What it indicates
    An unbalanced or overloaded load can stop the washer draining and spinning to avoid damage. The washer only runs with the lid or door securely closed. Gentle, delicate and handwash cycles spin slowly, so they leave more water in the clothes by design.
    What to do
    Redistribute the load evenly, or take some items out. Make sure the lid or door is fully closed. On a top-loader, select RINSE & SPIN to remove the excess water. For less water in future loads, use a cycle with a higher spin speed, such as Heavy Duty, when the care labels allow.
    If nothing changes
    If the washer still won't drain, contact Whirlpool or schedule service.

Brand-Specific Info

Error Codes

Sud / Sd
Too many suds to spin the water out. The washer pauses tumbling and adds water for extra rinses, which may repeat several times. Use HE detergent, avoid "no splash" or "easy pour" chlorine bleach, and make sure the drain hose and standpipe aren't kinked or clogged.
F9 E1
Drain time longer than expected, typically over eight minutes. Check the drain hose for kinks and clogs, use the U-shaped hose form, clean the drain pump filter and door-seal drain holes on front-loaders, and use HE detergent — excess suds also slow draining.
Int
The cycle was paused or canceled. The washer may take 20 to 30 minutes to stop spinning and drain. To clear it, press Pause or Cancel twice and Power once; if it stays, unplug the washer for 5 minutes.
Other F# E#
Unplug the washer for 5 minutes, reconnect it, reselect the cycle and press Start. If the code persists, request service.

During a Sd or Sud code the washer stops tumbling and adds water on its own. That pause is deliberate, to let the suds break down, so don't cancel it. After you pause or cancel a cycle, it can take 20 to 30 minutes to stop spinning and drain, with Int on the display.

The drain pump filter only exists on some front-load models. It's at the front bottom of the washer — behind the storage drawer on models that have one, otherwise behind an access panel. Whirlpool documents the user-cleanable pump filter only for front-load models. On top-loaders, water you can hear but not see is normally the fluid-filled balance ring at the top of the tub. Whirlpool documents the error codes above for front-load models. Top-loaders can show F9 E1 or dRN for a drain problem; check your owner's manual for your model.

What Not to Do

  • Don't use regular (non-HE) detergent, or more than the label calls for. Excess suds slow draining and spinning.
  • Don't tape the drain hose into the drainpipe. It needs an air gap to stop siphoning.
  • Don't push the drain hose far down into the standpipe. Use the U-shaped form so it sits at the right length.
  • Don't cancel a cycle while the washer is rinsing out suds. The pause and extra rinses are how it clears them.

Frequently Asked Questions

What does F9 E1 mean on a Whirlpool washer?

F9 E1 means draining is taking longer than expected, typically over eight minutes. Check that the drain hose isn't kinked or clogged, clean the drain pump filter if your front-loader has one, and make sure you're using HE detergent, because excess suds also slow draining.

What does Sd or Sud mean on a Whirlpool washer?

It means there are too many suds for the washer to spin the water out. The washer pauses and adds extra rinses to break them down, sometimes several times. Use HE detergent in the measured amount, and avoid "no splash" or "easy pour" chlorine bleach.

Where is the drain pump filter on a Whirlpool washer?

Whirlpool documents an accessible drain pump filter on some front-load models. It's usually at the front bottom of the washer, behind the storage drawer on models that have one. Your owner's manual shows whether your model has one and exactly where.

Why are my clothes still soaking wet after the cycle?

Usually it's too many suds, an overloaded or unbalanced load, or a gentle cycle that spins slowly on purpose. Use measured HE detergent, rebalance the load, and on a top-loader run RINSE & SPIN to remove the extra water.

I can hear water in my Whirlpool top-loader but can't see any. Is it draining properly?

That's normally the balance ring — a fluid-filled ring at the top of the tub. The fluid shifts to offset the load and keep the basket stable at high spin speeds. You may also hear it if you move the washer. It isn't water left over from the wash.

Related Problems